Airmar LB150 Weather Station not seeing any data

Home Forums Report a Bug or Issue Airmar LB150 Weather Station not seeing any data

This topic contains 1 reply, has 1 voice, and was last updated by  signalkaus 1 year, 12 months ago.

Viewing 2 posts - 1 through 2 (of 2 total)
  • Author
    Posts
  • #390

    signalkaus
    Participant

    I’ve got a Airmar LB150 WX Sensor I’m attempting to connect as the only input to the iKommunicate using NMEA0183. I have wired it correctly Port 1 input (Light blue wire) and ground. The sensor is powered as I can see the data also via a Y cable to my computer. It is throwing out data at 4800 correctly.
    The sentences currently being sent are:

    $GPVTG,324.8,T,313.8,M,0.1,N,0.1,K,A*27
    $HCHDT,351.7,T*29
    $WIMWV,194.0,R,3.2,N,A*2E
    $WIMDA,30.1472,I,1.0209,B,17.8,C,,,75.3,,13.3,C,184.6,T,173.6,M,3.2,N,1.6,M*60
    $YXXDR,C,,C,WCHR,C,,C,WCHT,C,,C,HINX,P,1.0191,B,STNP*43
    $GPZDA,012047,27,05,2017,00,00*4C
    $YXXDR,A,-6.7,D,PTCH,A,2.0,D,ROLL*73
    $HCHDT,351.7,T*29
    $WIMWV,191.0,R,2.8,N,A*20
    $GPGGA,012047,2731.2125,S,15317.0582,E,1,8,1.0,15.2,M,41.1,M,,*59
    $GPVTG,325.5,T,314.5,M,0.1,N,0.1,K,A*21
    $HCHDT,351.7,T*29
    $WIMWV,174.0,R,2.2,N,A*21
    $WIMDA,30.1442,I,1.0208,B,17.8,C,,,75.4,,13.3,C,164.8,T,153.8,M,2.2,N,1.1,M*6F
    $YXXDR,C,,C,WCHR,C,,C,WCHT,C,,C,HINX,P,1.0190,B,STNP*42
    $GPZDA,012048,27,05,2017,00,00*43
    $YXXDR,A,-6.6,D,PTCH,A,2.0,D,ROLL*72
    $HCHDT,351.7,T*29
    $WIMWV,173.7,R,1.9,N,A*29
    $GPGGA,012048,2731.2124,S,15317.0583,E,1,8,1.0,15.2,M,41.1,M,,*56

    However the Ikommunicate does not have the NMEA0183 light flashing, nor does it say it can see any valid NMEA sentences in Admin.

    Paul, can you confirm if the above sentences should be being parsed by the iKommunicate?

    I’ve tried swapping to NMEA input on port 2 without change.
    The iKommunicate is also running the latest v2 firmware.

    Thanks in advance.
    Justin

    #391

    signalkaus
    Participant

    This has now been resolved. Needed to to RX – to ground to see data

Viewing 2 posts - 1 through 2 (of 2 total)

You must be logged in to reply to this topic.

Comments are closed